Application of the hypoplastic model for validating direct shear tests to investigate the impact of fines on the behavior of chlef sand

Auteurs

  • Benali Nougar Innovative Materials Laboratory and Renewable Energies, Department of civil Engineering, Faculty of Science and Technology, University of Relizane, Bourmadia 48000 Relizane, Algeria
  • Abdelkader Brahimi University Center of Mila. Institute of Science and Technology. Civil Engineering and Hydraulics Department, Mila (Algeria). https://orcid.org/0000-0002-1853-388X
  • Djamel Edddine Bouri Ecole Nationale Supérieure d'Hydraulique, Blida, Algeria. https://orcid.org/0009-0003-0173-6271
  • Abdallah Krim University ibn khaldoun of Tiaret, Algeria.
  • Omar Safer Innovative Materials Laboratory and Renewable Energies, Department of civil Engineering, Faculty of Science and Technology, University of Relizane, Bourmadia 48000 Relizane, Algeria.
  • Kamel Menad Innovative Materials Laboratory and Renewable Energies, Department of civil Engineering, Faculty of Science and Technology, University of Relizane, Bourmadia 48000 Relizane, Algeria.
  • Ahmed Arab Hassiba Benbouali University of Chlef, Algeria. Laboratory of Materials Sciences and Environment (LMSE), Hassiba Ben Bouali University of Chlef (2000), Algeria.

DOI :

https://doi.org/10.18540/jcecvl10iss4pp18878

Mots-clés :

Sand, Silt, Clay, Fines Content, Shear Strength, Friction, Cohesion.

Résumé

This study was carried out to describe the mechanical behavior of different materials in terms of shear strength, cohesion and friction. For this purpose, an experimental shear tests were carried out. The soils used for the preparation of the samples were the Chlef sand, Chlef silt and M’zilla clay and a mixture composed of 50% of silt and 50% of clay. The soils were prepared by mixing Chlef sand with fines content of silt, clay or clay silt ranging from 0, 10, 20, 30 and 40%. The tests were conducted on sand samples prepared at a relative density of 20% representing a loose state and subjected to three normal stresses of 100, 200 and 400 kPa. All the tests were conducted at constant displacement rate of 1.00 mm/min. From the obtained results, it can be seen that the clean sand showed the highest shear strength at a small strains. At large strains, sands with 30% clay rather than 30% clay silt showed the highest shear strengths respectively. More contracted sands have the greatest increased maximum shear strengths. The sand with clayey silt, at a fine content of 20%, develops the most increased cohesion, among the other silty-clayey sands, together with the most reduced shear strength in elastic behavior. The sand with 40% of silt content develops a greater internal friction angle, however, the other silty sands, showed reduced shear strength, at the same behavior. To validate these findings, numerical simulations were performed on sand-silt mixtures using the hypoplastic model. The results indicated that the hypoplastic model accurately predicts the shear behavior of sand-silt mixtures in direct shear test, providing realistic insights into the effects of fines on the mechanical properties of the soil.

Keywords: Sand, Silt, Clay, Fines Content, Shear Strength, Friction, Cohesion.

Téléchargements

Les données relatives au téléchargement ne sont pas encore disponibles.

Bibliographies de l'auteur

Benali Nougar, Innovative Materials Laboratory and Renewable Energies, Department of civil Engineering, Faculty of Science and Technology, University of Relizane, Bourmadia 48000 Relizane, Algeria

Senior lecturer.

Abdelkader Brahimi, University Center of Mila. Institute of Science and Technology. Civil Engineering and Hydraulics Department, Mila (Algeria).

Senior lecturer

Djamel Edddine Bouri , Ecole Nationale Supérieure d'Hydraulique, Blida, Algeria.

Senior lecturer

Abdallah Krim, University ibn khaldoun of Tiaret, Algeria.

Professor

Omar Safer , Innovative Materials Laboratory and Renewable Energies, Department of civil Engineering, Faculty of Science and Technology, University of Relizane, Bourmadia 48000 Relizane, Algeria.

senior lecturer

Kamel Menad , Innovative Materials Laboratory and Renewable Energies, Department of civil Engineering, Faculty of Science and Technology, University of Relizane, Bourmadia 48000 Relizane, Algeria.

senior lecturer

Ahmed Arab, Hassiba Benbouali University of Chlef, Algeria. Laboratory of Materials Sciences and Environment (LMSE), Hassiba Ben Bouali University of Chlef (2000), Algeria.

Professor

Téléchargements

Publiée

2024-05-27

Comment citer

Nougar, B., Brahimi, A., Bouri , D. E., Krim, A., Safer , O., Menad , K., & Arab, A. (2024). Application of the hypoplastic model for validating direct shear tests to investigate the impact of fines on the behavior of chlef sand. The Journal of Engineering and Exact Sciences, 10(4), 18878. https://doi.org/10.18540/jcecvl10iss4pp18878

Numéro

Rubrique

General Articles

Articles les plus lus par le même auteur ou la même autrice